文章浏览阅读2.8k次,点赞2次,收藏3次。stm32mp157 盘古开发板 Linux内核版本4.19目录1、拜兔核i2SOM的wiki上关于gpio应用的说明2、gpio操作相关的数据结构3、测试代码:4、参考链接1、拜兔核i2SOM的wiki上关于gpio应用的说明链接:http://......
admin
文章浏览阅读580次。本来是要写一个linux驱动,用于控制led灯的,但考虑到nanopc-T4的内核已经帮我们配置好设备树,已经可以利用/sys/class/gpio操作gpio了,所以没必要再造轮子了! 在shell里,可以利用下面的命令控制Led灯的亮与......
admin
GPIO输入_stm32 如何一次检查gpioa所有的pin的变化...
admin
在上面一章,我们介绍了pwm子系统的框架以及数据结构等内容,而pwm 子系统中pwm_chip的注册与注销接口也就是实现pwm_chip与pwm_device之间的关联,并将pwm_chip放入系统pwm_chip链表中,而这些接口实现也较简单,就没有展开说明。本......
admin
文章浏览阅读2.7w次,点赞43次,收藏172次。一,引脚与端口:1.引脚就是芯片外接的引脚啊,一个芯片至少有VCC,GND引脚,象51单片机还有IO引脚,串口引脚等,引脚就是物理外接的一个个管腿啊。2.端口是单片机内部(CPU单元)......
admin
nanopi 2 fire s5p4418 初次体验 (3)编写一个简单的gpio驱动控制GPIOB30输出高低电平_nanopipc 修改设备树...
admin
要求为:ARM外部GPIO接收下降沿硬件中断,在中断回调函数中发送信号SIGIO给用户层,用户层异步接收到信号后在自身回调函数中做出一部分简单处理。具体要求很简单:外部4mS一个硬件中断(GPIO),如何实时传入Linux用户层,并......
admin
文章浏览阅读302次。(1)GPIO_Mode_IN_FLOATING 输入浮空模式。(6)GPIO_Mode_AF_OD 开漏复用输出模式。(8)GPIO_Mode_AF_PP 推挽复用输出模式。(5)GPIO_Mode_Out_OD 开漏输出模式。(7)GPIO_Mode_Out_PP 推挽输出模式。(2)GPIO_Mode_IPU 输入上拉......
admin
IX6MULL之汇编点亮LED灯一、原理分析1、查看原理图2、配置GPIO复用3、配置GPIO的电气特性一、原理分析IX6MULL是恩智浦公司的一款Coretex-A7系列的芯片,主频800M。LED点亮,其实就是最简单的GPIO控制的表现结果。对于GPIO的初始化,通......
admin
文章浏览阅读4.4k次,点赞3次,收藏44次。SPI、I2C、I2S、UART、GPIO、SDIO、CAN、JTAG的区别SPI全称及由来:SPI接口的全称是"Serial Peripheral Interface",意为串行外围接口,是Motorola首先在其MC68HCXX系列处理器上定义的。使用方法:SPI......
admin
输入一共有四种模式:模拟输入:多用在ADC转换或者DAC转换,或者配置一些闲时io口时进行省电上拉输入 :根据外部电路而来,给他一个上拉电阻,让这个模块默认电平为高下拉输入:浮空输入加一个下拉电阻闭合,默认低电平......
admin
友情链接申请要求: 不违法不降权 权重相当 请联系QQ:737597453